| Technical Data |
 |
| Volume capacity per kg. |
46 in3 / 750 cc |
| Mixed density |
0.048 lbs per in3 /
1.31 gm per cc |
Coverage rate per kg. @
12 mil/300 microns |
25 ft2 / 2.3 m2 |
| Shelf life |
Indefinite |
| Volume solids |
100% |
| Mixing ratio |
Base |
Activator |
| By volume |
2 |
1 |
| By weight |
3 |
1 |
|
Cure Times |
|
Ambient
Temperature |
Working
Life |
Touch Dry |
Maximum
Overcoat |
Full Cure |
| 59°F |
15°C |
90 min |
24 hrs |
48 hrs |
6 days |
| 77°F |
25°C |
70 min |
16 hrs |
24 hrs |
4 days |
| 86°F |
30°C |
55 min |
8 hrs |
16 hrs |
3 days |
|
Physical Properties |
|
| |
Typical Values |
Test Method |
| Compressive strength |
11,000 psi |
770 kg/cm2 |
ASTM D-695 |
| Flexural strength |
9,000 psi |
630 kg/cm2 |
ASTM D-790 |
| Hardness-Shore D |
86 |
|
ASTM D-2240 |
| Abrasion Resistance |
35 mg / 1,000
cycles |
ASTM D-4060 |
| Sheer adhesion - Steel |
4,100 psi |
287 kg/cm2 |
ASTM D-1002 |
|
Adhesion - to prepared cementitious surfaces primed with
ENECLAD CFS is greater than the cohesive strength of the
substrate. |
|
ENECLAD CFS Technical Data |
|
| Mixing Ratio |
Base |
Activator |
| By volume |
2 |
1 |
| By weight |
2.4 |
1 |
Ambient
Temperature |
Pot Life |
Minimum
Overcoat |
Maximum
Overcoat |
| 41°F |
5°C |
2 hrs |
3 days |
7 days |
| 59°F |
15°C |
40 min |
10 hrs |
36 hrs |
| 77°F |
25°C |
20 min |
5 hrs |
24 hrs |
| 86°F |
30°C |
15 min |
3 hrs |
16 hrs |
|
|
|
 |
|
|
|
Using ENECLAD FPS 2000 |
Surface Preparation - ENECLAD® FPS 2000 should only be
applied to clean, firm, dry, and well roughened surfaces.
1. Brush loose dirt from the surface to be treated and
remove all oil, grease and other surface and sub-surface
contamination using a solvent which leaves no residue such as
acetone, MEK, isopropyl alcohol, etc.
...for cementitious surfaces
2. Clean and roughen the surface by abrasive blasting,
steam cleaning, pressure washing or other suitable means.
3. Apply CHEMCLAD P4C Primer (see “Priming Concrete®
Surfaces”) and commence the application of ENECLAD FPS 2000
within the specified overcoating times.
...for metal surfaces
2. Thoroughly roughen the area to be treated by abrasive
blasting, insuring that the air used for this operation is free
of oil, water or other contaminants.
3. The grit blasting equipment and media should be
sufficient to yield a “white metal” surface and a minimum 3 mil
anchor profile.
4. Commence the application of the ENECLAD® FPS 2000
immediately upon completion of surface preparation.
Priming Concrete Surfaces - Prior to applying ENECLAD FPS
2000 to concrete and/or cementitious substrates, the surface
should be treated with ENECLAD® CFS to seal the surface and
insure optimum adhesion is obtained. After mixing, CFS should be
applied using a brush or roller at the rate of 125 square feet
(11 - 12 square meters) per kilogram to achieve the recommended
film thickness of 3 mils. Please note: coverage will be reduced
on excessively rough and/or porous surfaces. The application of
the ENECLAD® FPS 2000 may commence as soon as the applied CFS is
touch dry and should be completed within 24 hours of Priming.
For specific details concerning the use of the CFS, please refer
to the appropriate section of the ENECLAD® CFS Tech Sheet.
Mixing & Application - For your convenience, the
ENCLAD FPS 2000 Base and Activator have been supplied in
precisely measured quantities to simplify mixing of full units.
Should less than a full unit quantity of material be required, a
partial mix can be accomplished by mixing 2 parts Base to 1 part
Activator by volume (2:1, v/v).
Pour the entire contents of the Activator container into the
Base container. Mix the components thoroughly with a paint mixer
in an electric drill or other appropriate tool until the
material reaches a uniform, streak-free color. Scrape down the
sides and bottom of the container and re-mix.
Apply the mixed ENECLAD® FPS 2000 to the prepared surface using
a brush or roller, pressing firmly to insure thorough contact
with the prepared surface. Care should be taken to apply a
uniform thickness of approximately 12 mils over the area.
Where a non-slip surface is desired, apply two thinner coats of
ENECLAD® FPS 2000. After applying the first coat at about 6 - 8
mils, the selected aggregate should be sprinkled on and then
back-rolled into the layer. Within the specified overcoating
time, apply a second coat at a thickness of about 4 - 6 mils to
lock in the aggregate.
Health & Safety - Every effort is made to insure that
ENECON products are as simple and safe to use as possible.
Normal industry standards and practices for housekeeping,
cleanliness and personal protection should be observed. For
further information and guidance, please refer to the detailed
MATERIAL SAFETY DATA SHEETS (MSDS) supplied with the material
and also available on request.
Cleaning of Equipment - Wipe excess material from tools
immediately. Use acetone, MEK, isopropyl alcohol or similar
solvent as needed.
Technical Support - The ENECON® engineering team is
always available to provide technical support and assistance.
For guidance on difficult application procedures or for answers
to simple questions, call your local ENECON® Fluid Flow Systems
Specialist or the ENECON® Engineering Center.
|
|
All information contained herein is based on long-term testing in our laboratories as well as practical field experience and is believed to be reliable and accurate. No condition or warranty is given covering the results from use of our products in any particular case, whether the purpose is disclosed or not, and we cannot accept liability if the desired results are not obtained.
Copyright © 2008 by ENECON® Corporation. All rights reserved. No part of this work may be reproduced or used in any form or by any means - graphic, electronic or mechanical including photocopying, recording, taping or information storage and retrieval systems - without written permission of ENECON® Corporation. |
|
