A Sprayable Polymer Composite Coating System for Extraordinary Chemical Environments, at Elevated Temperatures
CHEMCLAD HT-XC is a two component, 100% solids, high performance, sprayable polymer system used for creating an outstanding corrosion and chemical resistant protective coating on all types of equipment and structures, at elevated temperatures.
CHEMCLAD HT-XC is simple to use - it mixes easily and can be sprayed. Since a minimum of two coats are recommended, CHEMCLAD HT-XC is available in two colors: cream and brown, to simplify overcoating. This self-leveling, high gloss coating yields a surface that is not only functional, but also aesthetically pleasing.
- Outstanding Chemical Resistance
- Apply by Spray
- 100% Solids
- Unlimited Shelf Life
- Simple to Use
- Durable
CHEMCLAD HT-XC is supplied in pre-measured quantities to simplify spray application of full units. ENECON recommends using the Graco E-Mix XT Plural-Component System for proportioning, mixing, and spraying two-component coatings. All instructions in the Graco E-Mix XT operation manual should be followed.
Colors
Brown
Cream
Note: Other colors are available on a “special order” basis. However, there are minimum / multiple quantity requirements for such orders and there may be an increase in cost. Additionally, due to formulation restrictions, not all colors are possible for all materials. Speak to your local ENECON Sales Representative for more information.
Due to monitor / printer differences, actual colors may vary slightly from the representations appearing in this chart.
Technical Data
- Volume capacity per kg.
- 30 in3 / 492 cc
- Mixed density
- 0.073 lbs per in3 / 2.03 gm per cc
- Coverage rate per kg. @ 12 - 15 mils
- 14 - 16 ft2 / 1.4 m2
- Shelf life
- Indefinite
- Volume Solids
- 100%
| Mixing ratio | Base | Activator |
|---|---|---|
| By Volume | 2.5 | 1 |
| By Weight | 2.3 | 1 |
Working Life and Cure Times
| Ambient Temperature | Working Life | Touch Dry | Maximum Overcoating | Full Cure | |
|---|---|---|---|---|---|
| 59°F | 15°C | 40 min. | 16 hrs. | 24 hrs. | 6 days |
| 77°F | 25°C | 30 min. | 8 hrs. | 16 hrs. | 4 days |
| 86°F | 30°C | 25 min. | 6 hrs. | 14 hrs. | 3 days |
Physical Properties
| Typical Values | Test Method | ||
|---|---|---|---|
| Compressive strength | 10,000 psi | ASTM D-695 | |
| Hardness - Shore D | 98 | ASTM D-2240 | |
| Tensile Shear Adhesion | |||
| Steel | 2,900 psi | 259 kg/cm2 | ASTM D-1002 |
| Aluminum | 2,400 psi | 189 kg/cm2 | ASTM D-1002 |
| Copper | 2,500 psi | 210 kg/cm2 | ASTM D-1002 |
| Stainless Steel | 2,700 psi | 245 kg/cm2 | ASTM D-1002 |
| Elcometer Adhesion - to properly prepared cementitious surfaces is greater than the cohesive strength of the substrate. | |||
Chemical Resistance
| Acetic acid (0-10%) | EX | Methyl alcohol | G |
| Acetic acid (10-20%) | G | Methyl ethyl ketone | G |
| Acetone | G | Naptha | EX |
| Aviation fuel (JP-4) | EX | Nitric acid (0-20%) | EX |
| Brake Fluid | EX | Phenol | G |
| Butyl alcohol | EX | Phosphoric acid (0-10%) | EX |
| Calcium chloride | EX | Phosphoric acid (10-20%) | EX |
| Carbon tetrachloride | G | Potassium chloride | EX |
| Chloroform | G | Propyl alcohol | EX |
| Crude oil | EX | Skydrol | EX |
| Diesel oil | EX | Sodium chloride | EX |
| Ethyl alcohol | EX | Sodium hydroxide | EX |
| Gasoline | EX | Sulfuric acid (0-20%) | EX |
| Heptane | EX | Toluene | EX |
| Hydrochloric acid (0-20%) | EX | Trichlorethylene | EX |
| Kerosene | EX | Xylene | EX |
EX - Suitable for most applications including immersion
G - Suitable for intermittent contact, splashes, etc.
NR - Not Recommended